您好!欢迎来到佛山市忠创金属制品有限公司官方网站!

在线留言收藏本站网站地图

忠创金属

艺术典范金属专家

全国咨询热线:0757-83137017

忠创坚持专业,品质制作未曾改变

Zcmetal 忠创金属艺术——不锈钢镜面板焊接注意事项

返回列表 来源: 发布日期: 2020.02.29

不锈钢镜面板焊接注意事项


金属的镜子应用的范围十分广泛,可用于洗手间、桌面摆设、化妆间、房间挂镜……而使用最多的材料莫过于不锈钢了,今天,忠创金属智造就给大家讲解不锈钢镜面板焊接注意事项。

Metal mirrors are used in a wide range of applications. They can be used in bathrooms, tabletop furnishings, dressing rooms, and room mirrors. The most commonly used material is stainless steel. Today, Zhongchuang Metal Zhizhi will explain the precautions for welding stainless steel mirror panels .


1镜框


不锈钢镜面板在焊接过程需要常常注意以下几个常见问题:

Stainless steel mirror panels need to pay attention to the following common problems in the welding process:


1洗手间镜框


首先,因为安装时为了防止尺寸的临时变化或计算误差而变短,往往其所用的镜面不锈钢板都会在尺寸上偏大;这会导致在其焊接的时候,其焊缝的宽度、长度、板材的实际厚度发生细微的中心线偏移;这就要求焊接的时候要控制该部位的位置尺寸大小。所以要保证所有构件下料准确而且长度允许的误差为1mm,还有构件在下料前也要查不锈钢镜面板是否平直。如果不平,则需要再进行矫平。

First of all, because the installation is shortened in order to prevent temporary changes in size or calculation errors, often the mirror stainless steel plates they use are too large in size; this will cause the width, length, and plate thickness of the welds when they are welded. The actual thickness of the center shifts slightly; this requires that the position and size of the part be controlled when welding. Therefore, it is necessary to ensure that all components are accurately blanked and the allowable length error is 1mm, and that the stainless steel mirror panel is straight before the components are blanked. If it is uneven, it needs to be leveled again.


1


其次,焊接的时候会常常出现裂纹,为了防止这种情况的发生,需要对焊接工艺的参数和程序有所把握,尽量不要使用大电流或者突然熄火,避免造成“焊疤”;而且焊缝的接头还需要接上10~15mm,焊接的过程注意不能敲击和搬动不锈钢镜面板,以免出现新的裂纹。不锈钢镜面板构件在焊接时候必须要把位置放置准备,焊点要牢固和饱满。尤其要注意的是焊缝表面的焊波应均匀,不得有裂纹、渣滓、焊瘤、烧穿、电弧擦伤、弧坑和针状气孔等缺陷,否则容易出现焊缝断裂和影响美观性。

Secondly, cracks often occur during welding. To prevent this from happening, you need to be certain of the parameters and procedures of the welding process. Try not to use large currents or sudden flameouts to avoid "welding scars." The connector also needs to be connected to 10 ~ 15mm. During the welding process, pay attention not to knock and move the stainless steel mirror panel to avoid new cracks. The components of the stainless steel mirror panel must be prepared during welding, and the solder joints must be firm and full. In particular, it should be noted that the welding wave on the surface of the weld should be uniform, and there must be no defects such as cracks, slag, weld knobs, burn-through, arc abrasion, arc pits, and pin-shaped pores, otherwise the weld seam is prone to break and affect the aesthetics.


2

5

3


最后,由于不锈钢镜面板的表面在研磨后,在去除氧化皮表面后,其表面会留有“针眼或气孔”,在焊接之前要将大部分的针眼或气孔刷洗干净,并且需要在焊接的过程中通过调节电流的大小而降低焊接的速度,保证焊接的均匀性;这样才能有效地避免“虚焊”现象的产生。而且镜面板在焊接组装完成后,还需要人工使用机具把板材的表面磨平和抛光,这样才使得外观保持平滑光亮。

Finally, because the surface of the stainless steel mirror panel is ground, after removing the oxide scale surface, there will be "pinholes or pores" on the surface. Before welding, most of the pinholes or pores must be cleaned, and it needs to be cleaned during the welding process. The speed of welding is reduced by adjusting the current to ensure the uniformity of welding; in this way, the phenomenon of "virtual welding" can be effectively avoided. In addition, after the mirror panel is welded and assembled, the surface of the plate needs to be polished and polished manually by using a machine, so that the appearance can be kept smooth and bright.


广东忠创智造科技有限公司是一家专于五星级酒店整体金属定制解决方案、户外艺术装置、室内外艺术品等的金属智造企业。

Guangdong Zhongchuang Intelligent Manufacturing Technology Co., Ltd. is a metal intelligent manufacturing enterprise specializing in five-star hotel overall metal customization solutions, outdoor art installations, indoor and outdoor artworks.


金属跟我们的生活变得越来越密不可分,应用的范围也十分的广泛,而我们忠创金属,是专业服务金属高端产品的整体解决方案个和系统落地执行者,专为客户解决有关金属产品的需要。忠创金属智造全诚为您服务。

The metal is becoming more and more inseparable from our life, and the scope of application is also very wide. Our loyalty metal is the overall solution for the professional service metal high-end products and the system floor performer, which is specially designed for customers. The need for metal products. Zhongchuang Metal Zhicheng is dedicated to serve you.


广东忠创智造科技有限公司

地址:广东省佛山市禅城区澜石石头村西便街一巷一号

体验馆展厅地址:广东省佛山市禅城区绿景一路盛南新都B区21号

电话:0757-83137017 82718158 28837249

联系人:燕燕、小洁、Waston(外贸)

联系电话:13411833248、18928697017、13928578824


Guangdong Zhongchuang Intellectually manufacturing Technology Co.,Ltd.

Address:No.5,1st Lane, Xibian Street,Lanshi Stone Village,Chancheng District,Foshan City,Guangdong Province

Exhibition Hall Address:No.21,Shengnan Xindu B District,Lujing Road, Chancheng District,Foshan City,Guangdong Province

Tel:0757-83137017 82718158 28837249

Contacts:Yanyan,Xiao Jie,Waston (Foreign Trade)

Contact numbers:13411833248,18928697017,13928578824

Website:www.zcmetal.net


欢迎电话、微信咨询了解!

Welcome to call, WeChat advice!

咨询热线

0757-83137017

0757-83137017 13929958201 380844484@qq.com 0757-28837249 广东省佛山市禅城区澜石石头村西便街一巷一号

扫一扫,手机站! 扫一扫,手机站!
扫一扫,手机站! 扫一扫,手机站!
忠创金属制品  版权所有  侵权必究  百度统计 CNZZ 备案号:粤ICP备19125579号 技术支持:牛商网(股票代码:830770)